Please note: This project is no longer active. The website is kept online for historic purposes only.
If you´re looking for a Linux driver for your Atheros WLAN device, you should continue here .

Senao / EnGenius

SL-3054PCI Aries

Chipset:AR5212(a/b/g)
URL:http://www.senao.com
Interface:PCI Interface Card
Antenna Connector:SMA connector with 2dBi whip
Device Information:ox168cx0013
Notes:wlanconfig ath0 list caps ath0=6782e40f<WEP,TKIP,AES,AES_CCM,HOSTAP,TXPMGT,SHSLOT,SHPREAMBLE,TKIPMIC,WPA1,WPA2,BURST,WME>
ticket:41 suggests these cards have some txpower problems, any confirmations?

3054CB Aries

Chipset:AR5212(b/g)
URL:http://datacom.engeniustech.com/...
Interface:Cardbus
Antenna Connector:No.
Device Information:ox168cx0013
Notes:Product has been EOLd. Variable TX power (to 200mW).

3054 MP ARIES2 4G

Chipset:AR5213 (b/g)
URL:http://www.netgate.com/product_info.php?cPath=26_34&products_id=155
Interface:MiniPCI Type IIIa card.
Antenna Connector:2 Hirose U.FL (MHF) leads.
Device Information:168c:0013, Subsystem: 168c:2026
Notes:Variable Transmit Output (Avg 802.11g 19 dBm 802.11b 19dBm all +/- 2dBm) Same as 5354 MP ARIES2 4G but no 802.11a leads

5354 MP ARIES2 4G

Chipset:AR5213 (a/b/g)
URL:http://www.netgate.com/product_info.php?cPath=26_34&products_id=109
Interface:MiniPCI Type IIIa card..
Antenna Connector:2 Hirose U.FL (MHF) leads.
Device Information:168c:0013, Subsystem: 168c:2026
Notes:Variable Transmit Output (Avg 802.11a 17 dBm,802.11g 19 dBm 802.11b 19dBm all +/- 2dBm)

NMP 8602 6G / EMP 8602 6G 400mW

Chipset:AR5006 (a/b/g)
URL:http://www.senao.com/english/product/product_wireless01_outdoor_1.asp?tp1id=02&tp2id=09&proid=000169
Interface:MiniPCI Type IIIB card..
Antenna Connector:2 Hirose U.FL (MHF) leads.
Device Information:168c:001b, Subsystem: 168c:2062 and 168c:2063
Notes:Expected availability: November 2005. Variable Transmit Output Avg 802.11a 20 dBm,802.11g 23 dBm 802.11b 26 dBm all +/- 2dBm. Card has been tested and operates correctly on Madwifi. A problem exists with WRAP boards which do not correctly detect the card on a cold boot. After a reboot the card works properly. WRAP boards with firmware 1.11 or newer cold boot properly and do not have this problem.
ticket:665 suggests these cards may be limited to 19dBm.
On ALIX boards; Card may smoke...from the ALIX2/3 manual; "Senao NMP-8602 PLUS high power radio cards are not supported at this time, pending an answer from Senao on power issues."
Please note: If you experience trouble with these cards in certain (especially embedded) boards, this could be due to power issues. This can not be fixed by the driver. See also #1780.

E-Mail PC Engines in regards to the ALIX / Senao EMP Problem, they have a fix!